Search Results

When a press signal is detected, the switch turns ON for 15 seconds then automatically turns OFF again.The ON time is extended by a further 15 seconds every time an additional press is detected.CompatibilityFor use with the Camtraptions Wireless PIR Sensor v3 ...

First press turns the switch ON, second press turns the switch OFF.CompatibilityFor use with:Camtraptions Wireless PIR Sensor v3 (purchased at any time), using video programs 4, 5 or 6.Camtraptions PIR Sensor v2 programs 14, 16, 18, 20, 22, 24.

The switch is ON while the press signal is held.

The switch has an inbuilt cut-out feature that automatically turns it off if it starts to overheat. This ensures that the switch itself does not get damaged.In practice, the switch can support devices drawing up to around 1.5 Amps for a prolonged period of tim...

The Camtraptions Sony Video Cable v2 is a cable with an integrated controller that allows remote video recording with Sony cameras featuring the Multi-type connector. The cable has been designed to work seamlessly with Camtraptions sensors and wireless trig...

Camera is woken, records for 15 seconds then automatically returns to the powered-down state. Recording time is extended by a further 15 seconds if there are additional full-press signals during the recording period. How It Works The input from full-press st...

Full-press starts recording, second full-press stops recording. How It Works The moment full-press is detected the camera is instructed to record. Recording stops only after full-press is released and a second full-press is detected. Note: This mode does no...

The Camtraptions Lens Heater system helps prevent your valuable camera trap images from getting spoilt by condensation, dew formation and fogging. The Lens Heater system consists of a programmable heating controller unit and a lens heater strip. Timer Func...

When this system is being used with the Camtraptions Camera Housing, it is recommended that you use the Heated Camera Housing Window (purchased separately), for the ultimate power-efficient and focused heating solution.

Please read these important safety warnings before using the Lens Heater. Important Safety Warnings: Only use power sources within range of 6V to 18V and rated to provide at least 1.5 Amps. The Lens Heater is not a toy. Please keep out of reach of children an...

The Lens Heater system consists of: Lens Heater Controller Lens Heater Strip 1. Lens Heater Controller USB Type A Socket, 5V Power Output DC 5.5mm x 2.5mm female socket, 6V–18V Power Input 2. Lens Heater Strip

Initial Setup First, connect the USB connector of the Lens Heater Strip into the USB Power Output socket of the Lens Heater Controller. Next, connect a suitable power source to the Power Input socket of the Heater Controller. The power source must have a volta...

Example 1 – Permanent Gentle Heating Scenario: The time is currently 08:33. I want the Lens Heater system to start warming my equipment immediately and to remain heating permanently (but only on a low power) until the battery is exhausted or until I disconnect...

Der Camtraptions DC Power Switch ist ein Kabel mit integriertem Controller, mit dem die Stromversorgung über einen Standard-Kameraauslöser ein- und ausgeschaltet werden kann. Das Kabel wurde für die nahtlose Zusammenarbeit mit Camtraptions-Sensoren, Funkauslö...

Wenn ein Drucksignal erkannt wird, schaltet sich der Schalter für 15 Sekunden EIN und dann automatisch wieder AUS. Die EIN-Zeit wird um weitere 15 Sekunden verlängert, jedes Mal wenn ein zusätzliches Drucksignal erkannt wird. Kompatibilität Zur Verwendung mit ...

Erstes Drücken schaltet den Schalter EIN, zweites Drücken schaltet den Schalter AUS. Kompatibilität Zur Verwendung mit: Camtraptions Wireless PIR Sensor v3 (zu beliebigem Zeitpunkt gekauft), mit Videoprogrammen 4, 5 oder 6. Camtraptions PIR Sensor v2 Programm...

Der Schalter ist EIN, solange das Drucksignal gehalten wird.

De Camtraptions DC Power Switch is een kabel met een geïntegreerde controller waarmee de stroomtoevoer kan worden in- en uitgeschakeld via een standaard camera-afstandsbediening. De kabel is ontworpen om naadloos samen te werken met Camtraptions-sensoren, dra...

Wanneer een indruksignaal wordt gedetecteerd, schakelt de schakelaar 15 seconden AAN en schakelt daarna automatisch weer UIT. De AAN-tijd wordt met 15 seconden verlengd telkens wanneer een extra indruk wordt gedetecteerd. Compatibiliteit Voor gebruik met de Ca...

Eerste indruk schakelt de schakelaar AAN, tweede indruk schakelt de schakelaar UIT. Compatibiliteit Voor gebruik met: Camtraptions Wireless PIR Sensor v3 (op elk moment aangeschaft), met videoprogramma's 4, 5 of 6. Camtraptions PIR Sensor v2 programma's 14, 1...